doc. no : qw0905-lur 9033/tr1 rev. : b date : 30 - jul - 2005 lur9033/tr1 data sheet ligitek electronics co.,ltd. property of ligitek only surface mount tape and reel lead-free parts pb
carrier type dimensions note : 1.all dimension are in millimeter tolerance is ? 0.2mm unless otherwise noted. 2.specifications are subject to change without notice. note : the tolerances unless mentioned is ? 0.2mm,angle ? 0.5. unit=mm. 2.8 0.16 4.0 0.4 ? 0.1 2.0 120.3 polarity 9.3 package dimensions part no. lur9033/tr1 0.4 3.32 1.75 1.5 4.0 5.5 2.16 0.3 4.85 cathode 2.0 r 1.9 1.4 0.7 2.5 4.6 ? 0.5 0.5 ? 0.1 ligitek electronics co.,ltd. property of ligitek only 1/7 page
r 178 ? 2.0 part no. lur9033/tr1 12.0mm tape,7"reel description quantity/reel 1500 devices 14.2 ? 1.0 74.0 ? 1.5 16.0 ? 1.0 reel dimensions page 2/7 ligitek electronics co.,ltd. property of ligitek only part no. lur9033/tr1
luminous intensity @20ma(mcd) min. 350 max 260 j for 5 sec max (2mm from body) color water clear note : 1.the forward voltage data did not including ? 0.1v testing tolerance. 2. the luminous intensity data did not including ? 15% testing tolerance. lur9033/tr1 part no emitted gaalas red material lens 660 peak wave length f pnm min. max. 1.5 20 2.4 forward voltage @20 ma(v) spectral halfwidth ??f nm typical electrical & optical characteristics (ta=25 j ) operating temperature storage temperature soldering temperature tstg tsol t opr -40 ~ +100 -40 ~ +85 typ. 20 650 viewing angle 2 c 1/2 (deg) j j ligitek electronics co.,ltd. property of ligitek only absolute maximum ratings at ta=25 j forward current peak forward current duty 1/10@10khz power dissipation reverse current @5v parameter ir pd i fp i f 10 120 120 40 symbol ratings ur g a mw ma ma unit page 3/7 part no. lur9033/tr1
ligitek electronics co.,ltd. property of ligitek only 0.0 0.8 forward voltage@20ma normalize @25 j relative intensity@20ma normalize @25 j wavelength (nm) ambient temperature( j ) fig.5 relative intensity vs. wavelength relative intensity@20ma 1.0 0.0 600 0.5 -40 -20 650 700 750 -40 80 20 04060100 ambient temperature( j ) -20 0 40 20 100 80 60 1 forward current(ma) relative intensity normalize @20ma fig.3 forward voltage vs. temperature 0.9 1.0 1.1 1.2 0 1 1.0 1.0 0.5 1.5 2.0 2.5 3.0 1 fig.4 relative intensity vs. temperature forward voltage(v) 3.0 2.0 4.0 0.0 5.0 0.5 forward current(ma) 100 10 1000 fig.1 forward current vs. forward voltage typical electro-optical characteristics curve 10 100 1000 ur chip fig.2 relative intensity vs. forward current 2.5 1.5 1.0 2.0 3.0 page4/7 part no. lur9033/tr1
1. hand solder basic spec is ?? 280 j 3 sec one time only. recommended soldering conditions 120 ~ 180 sec preheat rising +5 j /sec 60 ~ 120 sec 120 sec.max. reflow soldering should not be done more than two times. 150 3-2 pb-free reflow solder 1~5 c/sec 120 3-1. lead reflow solder 240 preheat temp. ( j ) 120 ~ 150 j 2. wave solder above 220c 60 sec.max. preheat 180~200 c 1~5 c/sec 260 c max. 10sec.max 5sec time cooling -5 j /sec soldering heat max. 260 j 245 ? 5 j within 5 sec ligitek electronics co.,ltd. property of ligitek only 5/7 page part no. lur9033/tr1
cleaning: use alcohol-based cleaning solvents such as isopropyl alc ohol to clean the led. (a) recommended circuit. (b) the difference of brightness between led could be f ound due to the vf-if characteristics of led. esd(electrostatic discharge): static electricity or power surge will damage the led. use of a c onductive wrist band or anti-electrosatic glove is recommended when handing these led. all devices, equipment and machinery must be properly grounded. led led circuit model a drive method: led is a current operated device, and therefore, require r some kind of current limiting incorporated into the driver circuit. this current limiting typically takes the form of a current limiting resistor placed in series with the led. consider worst case voltage variations than could occur across the current limiting resistor. the forwrd current should not be allowed to c hange by more than 40 % of its desired value. precautions for use: storage time: 1.the operation of temperatures and rh are : 5 j ~35 j ,rh60%. 2.once the package is opened, the products s hould be used within a week. otherwise, they should be kept in a damp proof box with descanting agent. considering the tape life, we suggest our customers to use our pr oducts within a year(from production date). 3.if opened more than one week in an atmos phere 5 j ~ 35 j ,rh60%, they should be treated at 60 j? 5 j fo r 15hrs. circuit model b ligitek electronics co.,ltd. property of ligitek only page 6/7 part no. lur9033/tr1
1.t.sol=235 j? 5 j 2.immersion time 2 ? 0.5sec 3.coverage ? 95% of the dipped surface solderability test mil-std-202f: 208d mil-std-750d: 2026 mil-std-883d: 2003 iec 68 part 2-20 jis c 7021: a-2 mil-std-750d:2031.2 j-std-020 mil-std-202f: 107d mil-std-750d: 1051 mil-std-883d: 1010 jis c 7021: a-4 environmental test ir reflow temperature cycling 1.105 j ~ 25 j ~ - 55 j ~ 25 j 30mins 5mins 30mins 5mins 2.10 cyeles 1.t=260 c max. 10sec.max. 2. 6 min mil-std-202f: 107d mil-std-750d: 1051 mil-std-883d: 1011 jis c 7021: b-12 mil-std-202f:103b jis c 7021: b-11 mil-std-750d: 1026 mil-std-883d: 1005 jis c 7021: b-1 mil-std-883d:1008 jis c 7021: b-10 page ligitek electronics co.,ltd. property of ligitek only 1.ta=under room temperature as per data sheet maximum rating. 2.if=20ma 3.t=1000 hrs (-24hrs, + 72hrs) thermal shock test high temperature high humidity storage test endurance test high temperature storage test low temperature storage test operating life test 1.ta=105 j? 5 j &-40 j? 5 j (10min) (10min) 2.total 10 cycles 1.ta=65 j? 5 j 2.rh=90 %~95% 3.t=1000hrs ? 2hrs 1.ta=-40 j? 5 j 2.t=1000 hrs (-24hrs, + 72hrs) 1.ta=105 j? 5 j 2.t=1000 hrs (-24hrs, + 72hrs) classification reliability test: test item test condition reference standard 7/7 part no. lur9033/tr1
|
